Moen garbage disposals are generally dependable and simple to use, but like any other disposal, they might have problems or be difficult to install and operate. You might save time and money on repairs or replacements by just trying to figure out what's wrong with your trash disposal.

The majority of reported problems are easily resolved by following simple troubleshooting methods. This instructional and problem solving guide will go through some of the most commonly reported issues with Moen garbage disposals and how to fix them.

The dependable Moen brand provides a wide range of effective trash compactors. Because of the clean, modern appearance, a few consumers have reported that they could not reset their devices.

Moen Garbage Disposal Reset Button

Moen Garbage Disposal Reset Button

The trash disposal reset button is simple to locate and operate. The reset button could be blamed if you turn on the power, but nothing happens. If it is displaced from its regular location, it indicates that the internal breaker has been tripped. It would be best if you now reactivated it. and you did the following: The garbage disposal system must be turned off.

Return the reset button to its original position with a screwdriver or equivalent equipment. Restart the garbage disposal and leave it to perform its work. Check to see if it starts working. If the reset button does not remain in the retracted position, something jams the trash disposal. You should turn the waste disposal off again if this is the case.

Moen Garbage Disposal Reset Button.

Check for potential obstructions to ensure the rotor is not obstructed—something harsh, such as a chunk of metal or tough cuisine. Examine the garbage disposal by shining a light down the drain. Remove any kind of obstruction from it. If you can't find the cause of the obstruction, insert a broom handle or garbage disposal wrench into the sinkhole and turn it until the disposer's rotor starts spinning freely.

Press the button again to restart the disposer. Wait 15 minutes before pressing the reset button. The broken trash disposal was probably caused by extra damage. An expert's assistance would be extremely beneficial in this situation.

Taking Out a Moen Trash Compactor Instructions

If the disposal is hardwired, unplug it, and if it isn't, turn off the power at the circuit breaker or fuse box. Remove the drain line from the tube that exits the garbage disposal using a wrench. If there is a dishwasher in the house, please turn it off.

Disconnect the dishwasher from the wall outlet or turn off the power at the panel. Take the disposal hose off the bottom of the dishwasher. Holding the disposal steady, twist the bottom mount ring to the left, and the disposal will come loose from the sink flange.

Try hammering on one of the mount's projections if the base ring won't budge. An accessory that comes with a number of different mounting systems are tubes that lengthen the mounting point. If a screwdriveris inserted into one of the tubes, the mounting ring can be rotated with greater force. There may be a clamp that needs to be unlocked before.

Step 4 is for you if your garbage disposal is hardwired. Move on to Step 5 if you're using an electrical cord. You need to shut off the power at the breaker or fuse box. Disconnect any hardwired connections or unplug the unit before attempting to remove the old disposal from the sink flange. Before purchasing replacement disposal, make sure the seals on your existing mounting ring are compatible with those of the new one. If the sink's original flange can't be reused, take it out.

This Moen Trash disposal is inoperable.

A wall-mounted switch controls the trash disposal. It is typically installed on the wall opposite the sink. You must hook the switch into a single power supply to function.

Is the trash disposal turned on with the stopper? The stopper activates the internal switch in the case. A broken or obstructed switch stops power from reaching the device.

Does a Garbage Disposal Need a Dedicated Circuit? - Tips
The numerous circuits sufficiently feed kitchens since they utilize the most power of any room in the house. It might imply that a kitchen with electrical cooking equipment requires as many as seven or eight circuits.
This button, which resembles a sink drain cap, activates the garbage disposal. The optic wire links the top deck switch to the lower deck outlet. Ascertain that the connection is secure and free of harm. Fiber optic switches had a short lifespan and are now obsolete. It is strongly advised to replace them with an air switch (ARC-4200 and AS-4201-finish).

To activate the trash disposal, press the switch's visible center button. The air switch positioned above the deck is linked to the outlet located below by a conduit. Ascertain that the connection is secure and free of harm. Repair or replace any broken connections.

What is the purpose of the "Reset" button?

If the garbage disposal overheats, you can restart it by pushing the reset button. Overloading trash disposal can happen for a variety of reasons. A possible cause is overcrowding of food leftovers inside the unit.

Beef bones, cutlery, and other hard food remnants may clog garbage disposal. When this happens, the built-in breaker in the disposer unit shuts the power, ensuring that no harm is done. The power is restored when the button is pressed again.

Look for a little hole on the bottom of the front side of the Moen trash disposal to reset it (the side that is not connected to an electrical outlet). Certain versions' reset buttons are tucked away and inaccessible without a long tool, such as a screwdriver.

When you use the Moen garbage disposal, the circuit breaker continues tripping

Because the shredding plate is stuck, the breaker may frequently trip when you turn on your Moen trash disposal. Check sure the breakers and switch are both turned off. If your device has a splash guard, it is recommended that you remove it immediately.

Then, using the flashlight, check for any debris lodged between the turntable and the grind ring, and remove it using tongs or needle nose pliers. After removing the foreign object(s), use a wooden spoon or unjamming wrench to press on the swivel impeller.

The entire turntable must be turn-able by hand by pressing the swivel impeller. The release is complete when the turntable can be turned a full revolution in either direction (clockwise or counterclockwise) without re-engaging the lock.

Share this post